Let's find your setup

Panels that snap together with connectors, forming the walls, shelves, backdrops, and structure of your entire display. Frosted finish diffuses light beautifully under event hall lighting and gives your setup a clean, premium look that wire grids can't match. Dimension: 35 x 35 cm | 13.78 x 13.78 in Weight: 157 g | 0.346 lb

The core connector of our system. These white hemisphere connectors snap into the corner holes of any panel and hold them together firmly. They handle 90-degree and 180-degree joins between panels. Press them in by hand or tap gently with the included hammer. Weight: 7 g | 0.015 lb

Everything is hand-press assembly. A small mallet assists by gently tapping connectors and panels together to fit snugly. Weight: 219 g | 0.483 lb

Panels that snap together with connectors, forming the walls, shelves, backdrops, and structure of your entire display. Frosted finish diffuses light beautifully under event hall lighting and gives your setup a clean, premium look that wire grids can't match. Dimension: 35 x 35 cm | 13.78 x 13.78 in Weight: 157 g | 0.346 lb

These panels exactly half the height of our standard square panels. You can use them to create tiered shelving for plushes and prints, shallow display buckets for sticker packs, or desk organisers along the front of your table. They add height and depth to your display without taking up extra table space. Dimension: 35 x 17.5 cm | 13.78 x 6.89 in Weight: 109 g | 0.24 lb

Same footprint as a standard square, but with a built-in hinge that changes how your whole front row works. You can use them to angle the bottom section of your display outward so customers can see stickers and flat items at a better viewing angle (perfectly pairs with our Foot Connectors), or use them as swing-open doors to hide your stock underneath. Dimension: 35 x 35 cm | 13.78 x 13.78 in Weight: 161 g | 0.355 lb

Our triangular panels let you add personality to your display. Use them as decorative roof peaks on a house-shaped gallery, corner shelves for featured items, or angled accents that make your setup instantly recognisable. Dimension: 35 x 35 cm | 13.78 x 13.78 in Weight: 128 g | 0.282 lb

You can use these panels to create dedicated hanging zones for prints, tote bags, hats, and heavier merchandise using standard grid hooks. You get all the hanging power of a traditional wire grid, but it slots right into your Boof setup instead of standing alone. Dimension: 35 x 35 cm | 13.78 x 13.78 in Weight: 211 g | 0.465 lb

Wire frame panels hold everything together without getting in the way - no blocked lighting, no visual clutter. Use them where you need support but don't want to block overhead lighting or obstruct the view into your display. They support your Boof structure without making it feel closed off. Dimension: 35 x 35 cm | 13.78 x 13.78 in Weight: 122 g | 0.269 lb

The core connector of our system. These white hemisphere connectors snap into the corner holes of any panel and hold them together firmly. They handle 90-degree and 180-degree joins between panels. Press them in by hand or tap gently with the included hammer. Weight: 7 g | 0.015 lb

Full 360 degree connectors that allow panels to connect from all directions at a single point. This lets you build displays that are two panels deep, create L-shaped corner setups, or wrap your display around a table corner. Weight: 10 g | 0.022 lb

Ground-level connectors that let you fan out the base of your display at an angle (in combination with our Hinged Square Panels). Instead of a straight vertical wall, you can tilt the bottom section forward so customers walking past actually see your work face-on instead of catching it edge-on. Especially worth it if you display prints or flat sticker sheets. Weight: 14 g | 0.031 lb

These connectors wrap around the outside corners of your display without the circular bulge of a standard hemisphere. Purely aesthetic: they give your setup a clean, finished look where exposed corners are visible. Weight: 4 g | 0.009 lb

Similar to corner connectors but designed for straight edges. They cap off exposed panel edges so there are no raw cuts or open connector holes visible. Another small finishing touch that separates a thrown-together display from one that looks intentionally designed. Weight 5 g | 0.11 lb

Single wire clips attach to the wire grid or wire frame panels at any point and let you rest a panel on them to create a shelf at any height you choose. One clip per side for lighter items. Weight: 0.6 g | 0.001 lb

Same concept as single wire clips but with double the grip. Use these when building shelves that will hold heavier items like plush toys, resin figures, or stacked print packs. They clamp onto wire panels and provide a stable platform for a panel to rest on. Weight: 1.6 g | 0.004 lb

Each hook attaches to wire grids via clip or to frosted panels via long-lasting adhesive that won't damage the surface. A single hook holds up to 7 enamel pins, 6 charms, or several fashion accessories. Customers can browse and grab what they want while you're helping someone else. Weight: 6 g | 0.132 lb

Everything is hand-press assembly. A small mallet assists by gently tapping connectors and panels together to fit snugly. More durable than standard wooden hammer. Weight: 248 g | 0.55 lb

A custom-sized carry tote designed to fit your entire Shapeshift kit. All panels stack flat, connectors go in the side pockets, and the whole thing carries like a bag. Makes load-in and load-out at events significantly faster and keeps everything organised between shows.